kitchen faucet white

kitchen faucet white

today i'm going to be showing you how to repaira leaking high-rise faucet. it's showing it's leaking at the neck here. see all the watercoming out? that's not right. it's going to be leaking down below, and we don't want that.anyway, for this repair, we don't need to turn the water off. if you have a single handlefaucet, for that type of repair you would need to turn the water off. a lot of times,this one you can do by hand, this one here. just turn it out. if you did need to use a pair of channel locks,you're going to want to protect your jaws with tape like so, to prevent marring theneck here. you also could use a strap wrench for this, which is a lot better than channellocks. because channel locks could deform


the neck if you were to squeeze it too tight,it could deform or reshape the neck as well as mark it up. but a strap wrench kind of grabs it, tightensdown and you can cinch it down and turn it out. but anyway, this one we can do by hand.inside here, there's three o-rings, and these are the o-rings that we're going to need toreplace here. now i already know my sizes of o-rings that i need, but if you don't knowwhat sizes you need, they do sell an o-ring kit. the stuff that i'm going to be usingis pretty stinky. it's this faucet grease here, and if you getit on your hands, it's pretty tough to wash off. because it's a high temperature faucetgrease and it's meant to not wash off with


water. when you go to repair this, you'regoing to want to wear gloves, and a good way to do this is to wear two or three pairs ofthese disposable gloves. you'll see reason i do this is this stuff'sso smelly. what you can do is unwrap the glove, one of the gloves, in order to use your toolsand not get the faucet grease all over your tool. not get the faucet grease all over theoutside of the faucet. this faucet is going to be in need of some cleaning afterwardsanyway, but that's another story. the easy way to get these o-rings off is touse a small flathead screwdriver. i've got one in my leatherman, so it comes in handyfor this. and it's just a matter of picking these off, fairly simple. if you keep themtogether, you can use that to size up your


new o-ring to make sure you're getting theright size. and all three of these are the same size, so you really only need to keepone together so if you needed to cut it, you could. not a big deal. okay. one, two, three o-rings,another reason for the gloves there. now what you want to do is coat this so that underneathit, it'll have a coating of the faucet grease. this stuff can be a little tricky to get apartsometimes, and mine's getting kind of old. it's time to order some more faucet grease.so anyway, go underneath where your o-rings are going to go. okay. now we'll slip ournew o-rings on. here's the first one. yeah, the gloves are going to make it a little tricky,but it's what it is, job security.


there's the second one, and number three.now we're going to coat the outside of the o-rings with the faucet grease. this is ahigh temperature faucet grease, so it's not going to come off with hot water, and lubingthis all around is going to prevent our o-rings from pinching up inside there. because if they pinch then they're going tobreak, and then your faucet's going to leak. okay, now that we got that, this is the goodtime to go ahead and remove that outer layer of the gloves. we can dispose of those. nowwe're ready to put our faucet neck back together. so we can slip this up, and then push it inall the way around gently, and then go ahead and slowly hand thread this in place so thatwe don't get it cross-threaded. we can get


rid of these, and we're just going to handtighten this down. once that's nice and tight...and now once that's nice and tight, just handtightened, we're going to prove it and check for any leaks. now if we see any leaks here, then can useour channel locks to tighten it up a little bit more, but it looks like everything's goodhere, no leaks. so now you want to check underneath for anyleaks, and you'll need to remove your gloves to do that. i'm going to take these off nowand check for any leaks down below. now first, you want to take your rag, dry everythingoff. it looks like we've got a loose handle there also. i'll show you how to tighten thatup, it's just an allen wrench under here,


it's real easy, but that's another story.i may put out another video how to tighten those down. i can try to put the link on thevideo here. going to come down below the sink and feelall around for any leaks. now, you may have to dry everything off and check this the followingday, as it was leaking before. so you probably have some water that's still trapped insidethere, so you're going to have to just keep an eye on this, and do what you can to dryit out. then go ahead and turn the water on. if yousee a flood of water, you know you've got a problem you've got to deal with. but ifyou're just feeling a little bit of moisture from before, you're actually okay.


an old trick is after you dry everything upbelow, is to put paper towels down, or toilet paper in order to check it. wow, there's somethingwrong here, someone skipped the air gap, that's not good for the dishwasher. you don't wantto do that. skipping that air gap can make you reallysick, because the air gap prevents the sewer gases from going into your food when it passesfrom your disposer, so you definitely don't want to run it straight in like this. this is wrong. so if you see this, you definitelywant to install an air gap to prevent getting harmful bacteria and everything into yourdishwasher. anyway, that's another story also. anyway, if we have no leaks here we're allset, good to go. one fixed high-rise kitchen


faucet. good to go.